|  HOME  |
| BENCHES | - | OPTIONS | - | e MAIL | - | CLEAN ROOM PRODUCTS | - | ESD PROPERTIES |- | CHAIRS |
 

      The unique characteristics of Nevamar Static Disipative Laminates make them ideally suited for a variety of electronically sensitive applications. Not only do they meet or surpass all standards for electrical properties, but they practically eliminate surface shedding. And they provide a tough, durable work surface that outlasts competitive materials.
 .....

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
Electrical Properties  




Volume Resistance; (100V, Face to Back)1 
Point to Point Resistance; (100V, 18" apart)1 
Decay Rate 
   (5000 Volts Fed Test Method 101C method 4046)2, 3 
Surface to Grounding Bolt (18" apart)1 


1 At 50% RH / 72o F, 100V with a Biddle BM 10 Megger Meter, 
NFPA Electrodes (2 1/2 Diameter, 5#) 
2 At 50% RH / 72o F 
3 Two seconds maximum allowed		 Typical 

107 
107 

.001 Sec.
 

107

 Certified 

1 x 106 to 1 x 109 
1 x 106 to 1 x 109 

Less than .05 sec. 
 

1 x 106 to 1 x 109
 
 
 
 

Typical NEMA Value 
Typical Rate of wear 
(weight loss per 100 cycles abrasion)

 Static Dissipative ARP SURFACE 

1550 cycles 
.006 gm/100 cycles		 Conventional (Non-ARP) 


600 cycles 
.080 gm/100 cycles
 
  • Laminate Performance Properties - Meets or exceeds NEMA LD-3-1991 standards for PF-42 grade.
  • Thickness - Postformable Sheet: .040" nominal   Lay-Flat Table Mat: .060" nominal
  • Formability - Postformable within 1/2" to 3/4" radius depending on equipment and humidity.
  • Surface Finish - Standard textured finish.
  • Bonding Procedure - Use standard contact or white glue adhesives, and standard (NEMA) application procedures for High Pressure Decorative Laminates. 
  • Chemical Resistance - Resistant to common solvents such as: Acetone; 111 Trichloroethylene; Solder Flux; Isopropyl Alcohol; Naptha.
  • Temperature Resistance - 350o F. with no change per NEMA LD-3.06 and NEMA LD-3.08.
  • Maintenance - Clean Static Dissipative Laminate with good ammoniated detergent, rinsing with clear water.  Do not use wax or other coaatings since they may modify the electrical properties of the laminate.
  • Installation - The laminate must be connected to a good ground to be effective. See Grounding Information section.
 
Check These Advantages: 
  • Controlled dissipation of static electricity without voltage supprression ambiguity.
  • Features ARP SURFACE to minimize surface shedding
  • Meets or exceeds all normal durability requirements of NEMA LD-3-1991
  • High resistance to hot solder, solder flux, chemicals and heat.
  • Textured Finish - easy to maintain.
  • Postformable for rounded applications
  • Each sheet is certified and labeled to meet specific electrical property requirements.
 
Color/Size Availability 

   Postformable Material, Product Code 740; Thickness .040," Nominal 
Pattern Number 

S-2-64
S-2-65
S-3-35
S-6-25
S-7-28
 		 Pattern Identification 

Beige
Almond
Blue
Gray
White
 		 Finish 

T
T
T
T
T
 		 Sizes In Stock 
36"x120" 36"x144" 48"x120" 48"x144" 60"x120" 60"x144"
 
X X X X X X
X X X X X X
X X X X X X
X X X X X X
X X X X X X
 
    Lay-Flat Table Mat Material, Product Code 720; Balanced Construction, Thickness .060," Nominal 
Pattern Number 

S-2-64
S-2-65
S-3-35
S-6-25
S-7-28
 		 Pattern Identification 

Beige
Almond
Blue
Gray
White
 		 Finish 

T
T
T
T
T
 		 Sizes in Stock 
36"x144" 48"x144" 60"x144"
X X X
X
X
X
X
X
X
X
X
X
X
X
X
 
 
  • Sheet Sizes Listted Are Nominal.
  • Finish "T" Indicates Standard Textured Finish.
  • 30" Width Available, Cut At No Charge, Order in Multiples Of Two.
  • Also Available In 96" Length with a 50 Sheet Minimum.

cover

 
info@tovarind.com